{"id":2762,"date":"2026-06-25T02:21:06","date_gmt":"2026-06-25T02:21:06","guid":{"rendered":"https:\/\/govelocks.com\/?p=2762"},"modified":"2026-06-25T02:25:18","modified_gmt":"2026-06-25T02:25:18","slug":"multi-function-door-control-panel","status":"publish","type":"post","link":"https:\/\/govelocks.com\/prs\/multi-function-door-control-panel\/","title":{"rendered":"Multi Function Door Control Panel Guide: Wiring &#038; Compatibility"},"content":{"rendered":"<p>We\u2019ve seen a single compatibility miss paralyze a loading dock for three days. The root cause wasn\u2019t a failed motor or a broken spring\u2014it was a wall console that couldn\u2019t talk to the operator. When you\u2019re managing a fleet of overhead doors across multiple facilities, a misordered <strong>multi function door control panel<\/strong> isn\u2019t just a return headache; it\u2019s a security gap and a maintenance bottleneck. Getting the console right means matching the operator\u2019s security protocol, wiring constraints, and access-control requirements before the first screw goes in.<\/p>\n<p>Our team regularly audits mixed-brand garage door operator fleets for commercial property groups, and the single most expensive mistake we see is buying generic \u201cuniversal\u201d panels for Security+ 2.0 systems. This guide walks through exactly what to check\u2014learn button colors, serial bus behavior, lockout protocols, and diagnostic patterns\u2014so your procurement decision doesn\u2019t become a field failure.<\/p>\n<h2>Understanding the Modern Multi Function Door Control Panel<\/h2>\n<p>A multi function door control panel is a wall-mounted interface that manages commercial and high-end residential overhead door operators. It controls basic door movement, configures operator light timers, locks the system against remote access, and programs wireless accessories directly from the console\u2014all over a low-voltage serial bus that goes far beyond simple contact closure.<\/p>\n<h3>Basic Door Control vs. Multi-Function Capabilities<\/h3>\n<p>A traditional bell-wire push button is a simple electrical shunt: press the button, close the circuit, and the door moves. Multi-function consoles, by contrast, send coded digital commands over a pair of low-voltage wires. This architecture enables features that a basic button can\u2019t support:<\/p>\n<ul>\n<li><strong>Light timer function:<\/strong> Programmable delay intervals (typically 1.5, 2.5, or 4.5 minutes, plus continuous hold) synchronize bay lighting with vehicle entry and exit patterns, which can reduce energy waste in warehouses.<\/li>\n<li><strong>Remote programming from the wall:<\/strong> Technicians can pair handheld remotes and wireless keypads using the on-console button instead of climbing a ladder to the operator head.<\/li>\n<li><strong>Lock mode (vacation lock):<\/strong> Disables all wireless remote signals while keeping the wired panel operational, an essential defense for after-hours facility security.<\/li>\n<li><strong>Diagnostic LED indicator:<\/strong> Provides immediate status feedback for wiring health, lock status, and programming mode.<\/li>\n<\/ul>\n<p><strong>Engineering takeaway:<\/strong> These panels communicate via low-voltage serial data, which means wire quality, connection integrity, and polarity are critical. A marginal connection that still rings out with a multimeter may still corrupt digital commands.<\/p>\n<h3>Auxiliary Smart Integration and MyQ Connectivity<\/h3>\n<p>Many modern consoles extend functionality through <strong>MyQ connectivity<\/strong>, an internet bridge that allows facility managers to monitor door status and control access remotely. When a multi function door control panel integrates with MyQ, the panel\u2019s light timer and lock commands can be triggered through enterprise dashboards or automated schedules. In mixed-use commercial buildings, this lets a property manager lock down all loading dock operators at 9 PM without physically walking the site. At <a href=\"\/prs\/gove-a8010-smart-door-lock-7-in-1\/\">Gove\u2019s 7-in-1 smart door lock<\/a>, we integrate similar remote-management logic into our access control interfaces, combining physical lockdown with cloud-based oversight.<\/p>\n<hr \/>\n<h2>Operator Compatibility: Matching Panels to Openers<\/h2>\n<p><strong>Decision rule:<\/strong> If your operator has a yellow learn button, you must use a Security+ 2.0 compatible multi function door control panel. Opening the wrong panel will not just fail to operate\u2014it can corrupt the operator\u2019s receiver logic and require a factory reset.<\/p>\n<h3>Security+ 2.0 and the Yellow Learn Button System<\/h3>\n<p>Chamberlain and LiftMaster\u2019s Security+ 2.0 protocol uses a tri-band frequency system operating on 310, 315, and 390 MHz with rolling-code encryption. The motor unit\u2019s yellow learn button identifies this generation. Compatible wall consoles, such as the <strong>LiftMaster 882LMW<\/strong> and <strong>Chamberlain 041A7185-1<\/strong>, communicate digitally over the two-wire bus and cannot be replaced by a simple push button or an older smart panel. Cross-wiring a legacy panel to a Security+ 2.0 opener often triggers a continuous flashing LED, indicating a protocol mismatch, and in some cases can send stray voltage back to the logic board.<\/p>\n<h3>Legacy Openers: Green, Red\/Orange, and Purple Learn Buttons<\/h3>\n<p>Older operators use different single-frequency and rolling-code systems that are electrically simpler and functionally independent. The table below provides a compatibility reference, but always verify panel compatibility directly with the operator manufacturer before bulk ordering.<\/p>\n<table>\n<thead>\n<tr>\n<th style=\"text-align: left\">Learn Button Color<\/th>\n<th style=\"text-align: left\">Protocol<\/th>\n<th style=\"text-align: left\">Compatible Panel Example<\/th>\n<th style=\"text-align: left\">Buyer Note<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Yellow<\/td>\n<td>Security+ 2.0 (tri-band 310\/315\/390 MHz)<\/td>\n<td>LiftMaster 882LMW, Chamberlain 041A7185-1<\/td>\n<td>Requires digital two-wire serial panel; legacy buttons will not work.<\/td>\n<\/tr>\n<tr>\n<td>Purple<\/td>\n<td>Security+ (315 MHz rolling code)<\/td>\n<td>LiftMaster 883LM, Chamberlain 041-0141<\/td>\n<td>Smart panels support basic door control and light, but lack MyQ on older purple-button units.<\/td>\n<\/tr>\n<tr>\n<td>Red\/Orange<\/td>\n<td>Security+ (390 MHz rolling code)<\/td>\n<td>LiftMaster 377LM, Chamberlain 935CB<\/td>\n<td>Often found on pre-2005 commercial jackshaft operators.<\/td>\n<\/tr>\n<tr>\n<td>Green<\/td>\n<td>Billion Code (fixed code)<\/td>\n<td>OEM wall push stations or dry-contact consoles only<\/td>\n<td>No multi-function smart panel compatibility; digital bus not supported.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><em>Always check the exact model number and learn button color on the operator chassis. Colors can fade or appear differently under facility lighting; confirm with the unit\u2019s specification plate.<\/em><\/p>\n<hr \/>\n<h2>Core Engineering Features of Commercial Wall Consoles<\/h2>\n<p>Industrial and commercial-grade multi function door control panels are built around a two-wire bus that carries both power and digital serial commands. This design simplifies installation while enabling lock mode, accessory pairing, and programmable light delays without running separate control circuits.<\/p>\n<h3>Two-Wire Serial Communication Bus<\/h3>\n<p>The panel connects to the operator\u2019s low-voltage terminal block via a pair of wires\u2014typically red and white\u2014that handle both DC power and bidirectional data. Unlike legacy buttons, where polarity rarely matters, modern serial consoles are <strong>polarity-sensitive<\/strong>. Reversing the wires may not damage the panel, but it will prevent data communication, causing a dead LED or a constant error blink. In commercial environments where wire runs can exceed 100 feet, maintaining clean, unbroken runs away from AC power lines is essential to avoid induced noise on the data channel.<\/p>\n<p><strong>What to verify:<\/strong> Always confirm that your low-voltage wiring does not share a conduit with high-voltage lines. In our facility audits, we\u2019ve traced intermittent phantom door operations directly to 120V AC cabling running less than 4 inches from unshielded bell wire.<\/p>\n<h3>Adjustable Light Timers and Motion Sensing<\/h3>\n<p>Most commercial panels include a customizable light timer that holds the operator\u2019s internal light on for a set interval after the door cycles. Common intervals are 1.5, 2.5, and 4.5 minutes, plus a continuous override for maintenance tasks. In warehouses with high-bay LED retrofits, we recommend the shortest practical interval to reduce electricity consumption without compromising safety. Some panels also accept a motion sensor input\u2014if occupancy is detected, the light timer resets, which keeps aisles illuminated during high-activity shifts and dark during idle periods.<\/p>\n<hr \/>\n<h2>Facility Security: Lockout Protocols and Access Control<\/h2>\n<p>The vacation lock button disables all wireless remote control signals at the operator receiver while keeping the wired wall console fully functional. For facility managers, this means during a holiday shutdown or weekend, a lost or cloned remote doesn\u2019t become a building access liability.<\/p>\n<h3>The Vacation Lock Button and Off-Hour Defenses<\/h3>\n<p>When the lock function is activated\u2014typically by pressing and holding the lock button for two seconds\u2014the operator\u2019s RF receiver section ignores any paired transmitter codes. The physical wall panel remains operational, so authorized personnel can still open the door with a keypad, card reader, or the console itself. In multi-tenant warehouses and mixed-use parking garages, we recommend integrating this lock mode into the facility\u2019s off-hours security protocol: lock all dock doors at the end of the last shift and require wired-only or personal credential access until the next morning.<\/p>\n<h3>Radio-Frequency (RF) Lockout Mechanics<\/h3>\n<p>The lockout works at the operator receiver stage, not at the transmitter. That means even if a cloned remote with a matched rolling code is used, the receiver won\u2019t process it while locked. This is particularly valuable in commercial environments with high remote hand-out turnover, such as logistics centers where temporary staff receive vehicle transmitters. For facilities concerned about advanced code-grabbing attacks, pairing this feature with a more sophisticated <a href=\"\/prs\/electronic-access-control\/\">electronic access control system<\/a> that uses encrypted credential readers adds a second authentication layer.<\/p>\n<hr \/>\n<h2>Step-by-Step Installation, Wiring, and Remote Programming<\/h2>\n<p>Installing a multi function door control panel requires running standard 2-conductor bell wire to the operator\u2019s low-voltage terminal block, with strict attention to polarity. Once wired, all accessory programming can be performed at the wall console, eliminating the need to reach the overhead operator.<\/p>\n<h3>Low-Voltage Terminal Block Connections<\/h3>\n<p>Follow this sequence to avoid damaging the panel or operator board:<\/p>\n<ol>\n<li>Disconnect power to the door operator at the breaker or pull the disconnect.<\/li>\n<li>Strip approximately 1\/4 inch of insulation from each conductor on 22 AWG solid copper wire.<\/li>\n<li>Identify the operator\u2019s red (R) and white (W) terminals and connect the corresponding panel wires. For most LiftMaster and Chamberlain commercial operators, red is positive and white is signal\/ground, but always verify with the wiring diagram on the operator.<\/li>\n<li>Secure the wall console to the junction box and restore power.<\/li>\n<li>Check the <strong>diagnostic LED indicator<\/strong>: a solid (non-flashing) light typically means power and data communication are normal.<\/li>\n<\/ol>\n<p><strong>Buyer warning:<\/strong> Do not exceed the manufacturer\u2019s recommended wire length for the panel. For 22 AWG, this is usually 150 to 200 feet. Beyond that, voltage drop and signal degradation can cause intermittent lockouts or failure to program remotes. If longer runs are unavoidable, move to 20 AWG or consider a <a href=\"\/prs\/poe-access-control\/\">PoE-powered control panel<\/a> with a local power supply at the door.<\/p>\n<h3>Syncing Handheld Remotes and Wireless Keypads<\/h3>\n<p>With the panel powered and the LED solid, programming accessories follows a Learn-button sequence on the console:<\/p>\n<ul>\n<li>Press and release the Learn or Program button on the wall panel. The LED will begin flashing.<\/li>\n<li>Within 30 seconds, press the button on the remote or enter the PIN on the wireless keypad and press Enter.<\/li>\n<li>The operator light will flash or the LED will go solid, confirming the code has been stored.<\/li>\n<li>Repeat for each additional transmitter.<\/li>\n<\/ul>\n<p>Programming from the wall panel is faster for maintenance teams because they don\u2019t need to reposition ladders or lifts to reach the motor unit. For facilities with dozens of remotes, we recommend pre-labelling each transmitter with a unit number and programming them in batches during a scheduled maintenance window.<\/p>\n<hr \/>\n<h2>Diagnostic Troubleshooting and Field Failures<\/h2>\n<p>Troubleshooting a non-responsive wall panel always starts with the diagnostic LED indicator. A blinking, dim, or unlit LED points to a wiring short, reversed polarity, or an overloaded accessory bus\u2014not necessarily a failed panel.<\/p>\n<h3>Decoding the Diagnostic LED Indicator<\/h3>\n<table>\n<thead>\n<tr>\n<th style=\"text-align: left\">LED State<\/th>\n<th style=\"text-align: left\">Meaning<\/th>\n<th style=\"text-align: left\">Action<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Solid ON<\/td>\n<td>Normal operation; power and serial bus intact.<\/td>\n<td>No action required; verify door operates correctly.<\/td>\n<\/tr>\n<tr>\n<td>Rapid flashing<\/td>\n<td>Lock (vacation) mode active, or panel is in programming mode.<\/td>\n<td>Disengage lock by pressing the lock button; if still flashing, check if learn button was pressed inadvertently.<\/td>\n<\/tr>\n<tr>\n<td>Slow blink (1\/sec)<\/td>\n<td>Operator board error or accessory bus overload.<\/td>\n<td>Disconnect all accessories and retest; replace panel only after confirming operator bus voltage.<\/td>\n<\/tr>\n<tr>\n<td>OFF (no light)<\/td>\n<td>No power or dead short on the wire run.<\/td>\n<td>Check terminal connections, test continuity of each conductor, and verify polarity.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><em>LED blink patterns can vary by manufacturer. Always consult the installation manual for the specific panel. The table above reflects patterns common to LiftMaster and Chamberlain commercial consoles.<\/em><\/p>\n<h3>Fixing Short Circuits and Phantom Operation<\/h3>\n<p>\u201cPhantom operation\u201d \u2014 where the door opens or closes without any input \u2014 is almost always a wiring issue. The two most common causes in commercial settings are a staple that has pierced the bell wire insulation and is intermittently shorting the pair, or moisture inside the wall console junction box creating a high-resistance path. When we see phantom operation, we start by isolating the wire run entirely: disconnect both ends and check resistance between the conductors. Any reading below several megaohms when dry indicates a fault. Replace the damaged section and ensure the panel gasket seals against the wall to prevent condensation ingress.<\/p>\n<hr \/>\n<h2>Procurement Framework: Selecting Multi-Function Panels at Scale<\/h2>\n<p>When sourcing multi function door control panels for multiple sites, standardization is the single largest cost-control lever. Procurement teams should lock in a single compatible panel model per operator type and avoid mixing aftermarket equivalents unless they\u2019ve been electrically validated by an engineer.<\/p>\n<h3>Bulk Procurement Specifications and Sourcing Metrics<\/h3>\n<p>We advise building a facility-wide door operator inventory before ordering replacements. For each operator, record the manufacturer, model, learn button color, approximate wire run length, and whether the existing panel is still functional. This data can go into a spreadsheet or CMMS (computerized maintenance management system). When quoting from a <a href=\"\/prs\/smart-door-lock-supplier\/\">smart door lock supplier<\/a>, provide the exact operator list to ensure the proposed panels are protocol-compatible, not just \u201cuniversal.\u201d For bulk orders of 50+ units, ask for serialized lot tracking; if a defect is found, you need to quarantine an entire lot, not just one panel.<\/p>\n<table>\n<thead>\n<tr>\n<th style=\"text-align: left\">Specification<\/th>\n<th style=\"text-align: left\">OEM Panel (LiftMaster 882LMW)<\/th>\n<th style=\"text-align: left\">Aftermarket Equivalent (Generic)<\/th>\n<th style=\"text-align: left\">Buyer Should Verify<\/th>\n<\/tr>\n<\/thead>\n<tbody>\n<tr>\n<td>Protocol Support<\/td>\n<td>Security+ 2.0 validated<\/td>\n<td>Often listed as \u201cuniversal\u201d or \u201ccompatible\u201d<\/td>\n<td>Request protocol test report or sample unit to test on a yellow-learn-button opener.<\/td>\n<\/tr>\n<tr>\n<td>Build Quality<\/td>\n<td>UL\u2011listed plastic enclosure, moisture-resistant gasket<\/td>\n<td>Thinner housing, inconsistent gasket seal<\/td>\n<td>Check for UL certification mark and IP rating if installed in damp locations.<\/td>\n<\/tr>\n<tr>\n<td>Bus Voltage Tolerance<\/td>\n<td>Designed for operator\u2019s regulated low-voltage bus<\/td>\n<td>May draw excessive current or be non-polarized<\/td>\n<td>Measure panel current draw with a milliammeter before permanent installation.<\/td>\n<\/tr>\n<tr>\n<td>Warranty &#038; Support<\/td>\n<td>1-year from manufacturer, technical support line<\/td>\n<td>Often limited or no direct support<\/td>\n<td>Confirm warranty terms and whether on-site troubleshooting is available.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<p><em>This table compares typical characteristics of OEM and aftermarket panels. Always request compliance documentation and, if possible, test a sample unit in a non-critical operator before full deployment.<\/em><\/p>\n<h3>Commercial Durability and Environmental Protection<\/h3>\n<p>In unconditioned spaces like loading docks or outdoor canopy areas, panel robustness matters. Look for sealed enclosures that prevent dust and moisture from reaching the PCB. Cheap aftermarket panels often lack conformal coating on the electronics, which can lead to corrosion in high-humidity environments. We also recommend specifying a panel with at least an IP54 rating if it will be installed where washdown or weather exposure occurs. That small additional cost prevents premature failure that disrupts shipping and receiving operations.<\/p>\n<p>Facility managers evaluating enterprise-wide upgrades should also consider the broader control architecture: for larger sites, a distributed <a href=\"\/prs\/edge-controller-architecture\/\">edge controller<\/a> can manage multiple door panels from a central location, reducing the number of physical consoles while still meeting local safety code requirements.<\/p>\n<hr \/>\n<h2>Partner with a Commercial Access Specialist<\/h2>\n<p>Upgrading door control systems across a large facility network requires careful hardware matching and strategic deployment planning. A compatibility mistake confined to one dock is annoying; multiplied across 40 locations, it becomes a budget and security crisis. Working with an access control specialist helps ensure the entire ecosystem\u2014wall panels, operators, MyQ bridges, and credential readers\u2014work together from day one.<\/p>\n<p>We regularly assist property groups and logistics firms with bulk compatibility audits and pre-deployment testing. When you reach out, have a list of current overhead operator models, learn button colors, estimated wire run lengths, and total facility unit counts ready. This lets us propose a tailored panel package that standardizes your fleet without surprises. For integrated solutions that combine multi-function panels with broader building access, explore our <a href=\"\/prs\/solutions\/\">access control solutions<\/a> or discuss custom runs with our <a href=\"\/prs\/smart-lock-manufacturer-in-china\/\">OEM production team<\/a>.<\/p>\n<hr \/>\n<h2>Frequently Asked Questions<\/h2>\n<h3>Can I use a Security+ 2.0 control panel on an older door operator?<\/h3>\n<p>No. A Security+ 2.0 panel requires the digital serial communication bus present on yellow learn button operators. It is not backwards-compatible with green, red\/orange, or purple learn button units that expect simple contact closure or older rolling-code schemes. Connecting them can cause the operator to lock out or display constant error codes.<\/p>\n<h3>Why is the LED light on my multi function door control panel flashing rapidly?<\/h3>\n<p>Rapid flashing almost always indicates that the vacation lock mode is engaged, blocking all wireless remote signals, or that the panel is currently in programming mode and waiting for a remote signal. Disengage the lock by pressing the lock button again, or wait for the programming window to time out.<\/p>\n<h3>How do I override the vacation lock function if my wall button is unresponsive?<\/h3>\n<p>If the wall button is completely dead, go to the operator motor head. On most commercial units, you can clear the lock by pressing and holding the learn button on the operator for six seconds, then pressing it again. If the button is unresponsive due to a wiring fault, power-cycle the operator and then re-address the lock setting.<\/p>\n<h3>Can you run multiple multi function door control panels to a single door operator?<\/h3>\n<p>No. The digital serial bus does not support multiple master smart panels on the same circuit\u2014the addressing conflict will cause both to malfunction. To add a second control point, use a standard dry-contact push-button station wired in parallel, if the operator board supports parallel dry-contact inputs. For more advanced multi-station setups, consider a <a href=\"\/prs\/commercial-access-control-locks\/\">commercial door control system<\/a> that routes commands through a central access controller.<\/p>\n<h3>What wire gauge is recommended for connecting a wall control panel?<\/h3>\n<p>22 AWG solid copper bell wire is the standard. For runs under 150 feet, it provides sufficient current and data integrity. If your run exceeds 200 feet, upgrade to 20 AWG or install a local auxiliary power supply. Using wire thinner than 24 AWG risks voltage drop and serial communication errors, which often appear as intermittent lockouts or failure to program remotes.<\/p>","protected":false},"excerpt":{"rendered":"<p>We\u2019ve seen a single compatibility miss paralyze a loading dock for three days. The root cause wasn\u2019t a failed motor [&hellip;]<\/p>\n","protected":false},"author":1,"featured_media":2767,"comment_status":"open","ping_status":"open","sticky":false,"template":"","format":"standard","meta":{"site-sidebar-layout":"default","site-content-layout":"","ast-site-content-layout":"default","site-content-style":"default","site-sidebar-style":"default","ast-global-header-display":"","ast-banner-title-visibility":"","ast-main-header-display":"","ast-hfb-above-header-display":"","ast-hfb-below-header-display":"","ast-hfb-mobile-header-display":"","site-post-title":"","ast-breadcrumbs-content":"","ast-featured-img":"","footer-sml-layout":"","ast-disable-related-posts":"","theme-transparent-header-meta":"","adv-header-id-meta":"","stick-header-meta":"","header-above-stick-meta":"","header-main-stick-meta":"","header-below-stick-meta":"","astra-migrate-meta-layouts":"set","ast-page-background-enabled":"default","ast-page-background-meta":{"desktop":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"ast-content-background-meta":{"desktop":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"tablet":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""},"mobile":{"background-color":"var(--ast-global-color-5)","background-image":"","background-repeat":"repeat","background-position":"center center","background-size":"auto","background-attachment":"scroll","background-type":"","background-media":"","overlay-type":"","overlay-color":"","overlay-opacity":"","overlay-gradient":""}},"footnotes":""},"categories":[22],"tags":[],"class_list":["post-2762","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-industry-knowledge"],"_links":{"self":[{"href":"https:\/\/govelocks.com\/prs\/wp-json\/wp\/v2\/posts\/2762","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/govelocks.com\/prs\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/govelocks.com\/prs\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/govelocks.com\/prs\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/govelocks.com\/prs\/wp-json\/wp\/v2\/comments?post=2762"}],"version-history":[{"count":2,"href":"https:\/\/govelocks.com\/prs\/wp-json\/wp\/v2\/posts\/2762\/revisions"}],"predecessor-version":[{"id":2768,"href":"https:\/\/govelocks.com\/prs\/wp-json\/wp\/v2\/posts\/2762\/revisions\/2768"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/govelocks.com\/prs\/wp-json\/wp\/v2\/media\/2767"}],"wp:attachment":[{"href":"https:\/\/govelocks.com\/prs\/wp-json\/wp\/v2\/media?parent=2762"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/govelocks.com\/prs\/wp-json\/wp\/v2\/categories?post=2762"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/govelocks.com\/prs\/wp-json\/wp\/v2\/tags?post=2762"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}